deliveryhasem.blogg.se

2016 international body control module location

#2016 INTERNATIONAL BODY CONTROL MODULE LOCATION MANUAL#
#2016 INTERNATIONAL BODY CONTROL MODULE LOCATION CODE#
#2016 INTERNATIONAL BODY CONTROL MODULE LOCATION PASSWORD#

NOTE – The available source addresses will vary depending on each vehicle configuration. Refer to Source Addresses (SA) for more information.įMI=0 – Data Valid But Above Normal Operational Range – Most Severe LevelįMI=1 – Data Valid But Below Normal Operational Range – Most Severe LevelįMI=2 – Data Erratic, Intermittent Or IncorrectįMI=3 – Voltage Above Normal, Or Shorted To High SourceįMI=4 – Voltage Below Normal, Or Shorted To Low SourceįMI=5 – Current Below Normal Or Open CircuitįMI=6 – Current Above Normal Or Grounded CircuitįMI=7 – Mechanical System Not Responding Or Out Of AdjustmentįMI=8 – Abnormal Frequency Or Pulse Width Or PeriodįMI=12 – Bad Intelligent Device Or ComponentįMI=15 – Data Valid But Above Normal Operating Range – Least Severe LevelįMI=16 – Data Valid But Above Normal Operating Range – Moderately Severe LevelįMI=17 – Data Valid But Below Normal Operating Range – Least Severe LevelįMI=18 – Data Valid But Below Normal Operating Range – Moderately Severe LevelįMI=31 – Condition Exists SOURCE ADDRESSES (SA) This number identif es the module reporting the fault. This number represents the number of times a fault has gone from previously active to active.

Active” or “Previously Active” will be displayed to identify whether a fault is currently active or if the fault was previously active.

Refer to Failure Mode Indicators (FMI) below for more information. This number represents the type of failure detected. This number identif es the item for which diagnostics are being reported.

“SPN” represents the Suspect Parameter Number.

Some previously active codes may not be cleared by this method. Previously active diagnostic trouble codes can only be cleared by a service tool, such as Diamond Logic® Builder (DLB). The following information will be displayed for each fault: SPN : FMI OCĭTC Description CLEARING DIAGNOSTIC TROUBLE CODES Scroll through the list of faults if faults are present. The VID will indicate “NO FAULT DETECTED” if faults are not found.

#2016 INTERNATIONAL BODY CONTROL MODULE LOCATION MANUAL#

Refer to the Vehicle Information Display Owner’s Manual for more information.

#2016 INTERNATIONAL BODY CONTROL MODULE LOCATION PASSWORD#

The VID may initiate a password prompt if the VID has been password protected. NOTE – The following selections will not be available if the vehicle is not equipped with the option to display codes.ģ. Perform the following steps if all of the above conditions are met:

The feature is not password protected to prevent unauthorized access.

The vehicle is not moving (the Vehicle Speed is equal to zero).

AND the programmable parameter “Diagnostics” is enabled using Diamond Logic® Builder (DLB).

AND displaying codes is allowed due to vehicle orderable options.

The key switch is in the IGNITION position.

NOTE – The VID will display “Not Available” if a DTC description is not available for a particular fault.ĭisplaying codes will only be allowed if all of the following conditions are true: Source addresses and DTC descriptions are presented in plain text. Suspect parameter number (SPN), failure mode indicator (FMI) and occurrence count numbers are listed. The VID can be used to display all diagnostic trouble codes (DTC) on the vehicle. Displaying Codes on the VID (if equipped) NOTE – Turning the key switch off, turning the key switch to the CRANK position, or releasing the park brake will take the gauge cluster out of the diagnostic mode. The following information will be displayed for each fault: To manually cycle through the fault list press and release the cluster display selector button. Once all faults have been displayed the number of faults will be displayed again, then the cycle will repeat.

#2016 INTERNATIONAL BODY CONTROL MODULE LOCATION CODE#

If faults are present, the gauge cluster display will show each diagnostic trouble code for 10 seconds and then automatically scroll to the next entry and continue to cycle through the faults. NOTE – The gauge cluster will only display “Software Rev” and “Hardware Rev” for 5 seconds followed by the message “Diagnostic Trouble Codes are not available” if the vehicle is not equipped with the option to display codes. The gauge cluster will then display the following information for 5 seconds:

Momentarily press the Cruise “ON” switch and the Cruise “Resume” switch at the same time.Ī gauge sweep will be performed on the gauges.

Turn the key switch to the IGNITION position to view both active and previously active codes.

Turn the key switch to the ACCESSORY position to view only previously active codes.

To display codes on vehicles not equipped with a VID: VEHICLES EQUIPPED WITH OPTION TO DISPLAY CODES Displaying Codes on the Gauge Cluster (Non-VID equipped vehicles)